「沈阳厂房机械门封」海绵门封和机械门封的优势对比

「沈阳厂房机械门封」海绵门封和机械门封的优势对比

The Advantages of Sponge Door Seal and Mechanical Door Seal in Shenyang Workshop


 

工业门的高密度海绵门封与机械门罩对比在于，挤压式门封更能合理地填充封闭式大货车与工作领域间的缝隙，并且成本费用较低



Comparing the high density sponge door seal with the mechanical door cover, the extrusion door seal can fill the gap between the closed truck and the working field more reasonably, and the cost is lower.

但与此同时，门封的厚度会引货台门洞的净宽缩减，偶尔会影响托板流畅地出入库大货车。



However, at the same time, the thickness of the door seal will reduce the net width of the entrance of the cargo platform, occasionally affecting the smooth access of pallets to and from the warehouse truck.



还有在其它情形下，大货车尾端有外伸的托板时，门封的运用会面临不良影响。



In other cases, when the truck rear end has an extended bracket, the use of door seals will face adverse effects.



工作领域门宽大于2.8米或高于3.0米时，不可以接纳门封。



Door seals are not acceptable when the width of the work area door is larger than 2.8 meters or higher than 3.0 meters.

工业门门封的封垫内间隔宽度计划方案成2.2- 2.3米宽度为好，门封可适应大部分的大货车。



The width of the gap in the gasket of industrial door seals is planned to be 2.2-2.3 meters wide. The door seals can be adapted to most large trucks.



货车工作领域门宽于2.3米时，需接纳斜角封垫。



When the truck working area door is wider than 2.3 meters, inclined gaskets should be accepted.



门封上端封垫的边沿底需低于大货车后顶部非常少8公分。



The edge and bottom of the top sealing pad of the door seal should be very little 8 cm below the top of the rear of the truck.



门封上端封垫可按照大货车高度的需要而上下调整。



The top sealing pad of the door seal can be adjusted up and down according to the height of the truck.



领域门较高且大货车高度条件过大时，接纳调整的垂帘形成蓬式门封替代上端封垫。



When the field door is high and the height condition of the truck is too large, the adjustable drapes are adopted to form a canopy door seal instead of the upper seal.



「沈阳厂房机械门封」海绵门封和机械门封的优势对比



The Advantages of Sponge Door Seal and Mechanical Door Seal in Shenyang Workshop



挑选挤压式海绵门封的常见问题：



Common problems in selecting extruded sponge door seals:



1.封垫对墙面造成的压力约为每米120千克。斜角封垫约为一半。



1. The pressure on the wall caused by the cushion is about 120 kilograms per meter. The bevel gasket is about half.



2.房屋建筑墙面到防撞胶平面非常少要有10厘米的间隙，为门封挤压后的壁厚留有余地。



2. There is very little gap of 10 centimeters between the wall of building and the collision-proof glue plane, leaving room for the wall thickness after the door seal is extruded.



3.封垫的厚度应高于防撞胶平面10到20厘米，高过15厘米更是为宜。



3. The thickness of the gasket should be 10 to 20 centimeters higher than the collision-proof glue plane, and 15 centimeters higher is more appropriate.



4.装卸区路面倾斜度超过2%时，应接纳锥壮封垫。




4. When the gradient of the road surface in the loading and unloading area exceeds 2%, the conical seal shall be adopted.



倾斜度每提升一个百分之一，封垫顶端厚度比底部厚度应小2.5厘米。



The top thickness of the gasket should be 2.5 centimeters less than the bottom thickness for every 1% increase in the inclination.